A tankless water heater needs regular descaling, which means circulating a descaling solution through the unit to dissolve mineral buildup inside the heat exchanger. Most manufacturers call for this at least once a year, and anywhere the water carries minerals, including much of North Texas, the technicians at Justice Plumbing regularly see units that need it sooner. Skipping it costs you efficiency, triggers error codes, shortens the unit’s life, and can put your warranty at risk.
If you went tankless for the endless hot water and lower energy use (here are a few more reasons homeowners love tankless), descaling is the upkeep that protects those benefits. Below you’ll find what hard water does inside the unit, the warning signs to watch for, and a complete walkthrough for flushing a tankless water heater yourself.
-SiMOSVBONcu5rCOvHf6RFzoYyV9zK1.jpeg&w=3840&q=75)
Why Hard Water Is the Deciding Factor
Hard water is water carrying dissolved calcium and magnesium. It’s measured in grains per gallon (gpg) or milligrams per liter (mg/L, the same as parts per million). One grain per gallon equals about 17.1 mg/L.
Here’s the general scale:
- Under 3.5 gpg (60 mg/L): soft
- 3.5 to 7 gpg: moderately hard
- 7 to 10.5 gpg: hard
- Over 10.5 gpg (180 mg/L): very hard
So how hard is the water in Granbury? According to TapWaterData, which compiles utility-reported water quality results, Granbury’s tap water averages about 4.9 grains per gallon (84.4 mg/L), which lands in the moderately hard range. That may not sound dramatic, but a tankless heat exchanger is far less forgiving than a faucet or a dishwasher. Even moderate hardness leaves scale behind every time water flashes to temperature, and homes on private wells around Hood County can run considerably harder than city water.
The chemistry is simple. A tankless unit pushes water through a heat exchanger and heats it fast, often to 120°F or higher in a matter of seconds. Heat forces dissolved minerals out of the water, and they settle on the exchanger walls as a hard, chalky crust called scale. Harder water speeds that up, but softer water doesn’t stop it.
Tankless units feel this more than traditional tanks do. A tank has 40 or 50 gallons of space where sediment can settle and sit for a while. A heat exchanger has narrow passages, sometimes only a fraction of an inch wide, with nowhere for scale to hide, so every layer narrows the path. Many manufacturers also list water quality limits in the owner’s manual, so it’s worth comparing your water to what your manual says. If you’re over the limit, take a look at water treatment options for your home.
What Scale Buildup Does to a Tankless Unit
Reduced Efficiency and Higher Gas Bills
Scale is a surprisingly good insulator. As it coats the heat exchanger, heat from the burner has a harder time reaching the water. The burner compensates by firing harder and longer to hit the same temperature. You pay for that extra fuel every month, and the efficiency you bought the unit for slowly disappears.
Restricted Flow and Lower Hot Water Output
As the passages narrow, less water moves through the exchanger. You’ll notice weaker pressure at hot taps, or the unit struggling when two showers run at once. Most tankless units also need a minimum flow rate to fire at all, so restricted flow can keep the burner from kicking on at low-volume fixtures like a bathroom sink.
Temperature Swings and the Cold Water Sandwich
Some brief cold water between bursts of hot is normal with tankless units. Scale makes it worse. When the unit can’t read and respond to water temperature accurately, you get hot, then a blast of cold, then hot again. Showers start to feel unpredictable.
Error Codes and Lockouts
Modern tankless units monitor themselves, and when scale causes overheating or flow problems, the unit throws an error code and may shut down to protect itself. Scale-related faults are among the most common reasons for tankless service calls. If descaling doesn’t clear the code, a sensor or component may need professional water heater repair.
Shortened Lifespan
A well-maintained tankless water heater can run 20 years or more, roughly twice as long as a typical tank. Neglected, a unit can fail far short of that. Scale causes hot spots on the heat exchanger, and that repeated thermal stress can crack it. A replacement exchanger often costs a large share of what a new unit does.
Voided Warranty
This is the detail almost nobody mentions. Most major manufacturers exclude scale damage from warranty coverage, and many expect proof of regular maintenance before they’ll honor a heat exchanger claim. If your exchanger fails at year six and you can’t show service records, you could be paying for it yourself. Check your owner’s manual for your brand’s specific requirements.
Signs Your Tankless Water Heater Needs Descaling
- Hot water takes longer to reach the tap than it used to
- Water temperature swings during a shower
- Hot water flow feels weaker at faucets and showerheads
- An error code appears on the display (your manual lists which codes point to scale)
- The unit cycles on and off more often
- You see white mineral crust on fixtures or on the unit’s inlet filter screen
- It’s been more than 12 months since the last service
- The unit makes rumbling, knocking, or popping sounds
How Often Should a Tankless Water Heater Be Descaled?
For most households, once a year is the manufacturer baseline, and that’s the minimum rather than the target.
- Moderately hard city water with no softener: at least once a year
- Whole-home water softener installed: annually is usually enough
- Large household or heavy hot water use: every 6 to 12 months
- Private well or very hard water: often every 6 months, depending on test results
Some newer units have a built-in scale detection feature that alerts you when buildup reaches a certain level. If yours does, treat that alert as a hard deadline.
How to Flush and Descale a Tankless Water Heater
A full flush takes about 90 minutes to 2 hours, most of it waiting on the pump. If you own an electric tankless unit, check the manual first, since some models use a different procedure.
What you’ll need:
- A small submersible utility pump
- Two washing machine hoses (or the hoses from a tankless flush kit)
- A 5-gallon bucket
- 3 to 4 gallons of undiluted white vinegar or a manufacturer-approved descaling solution
Never use bleach, chemical drain cleaner, or any harsh chemical in a heat exchanger. They can damage internal components.
Before you start, check for isolation valves. These are the service valves on the hot and cold lines below the unit, each with a small side port and a cap. Many installed units don’t have them. Without isolation valves, there’s no practical way to flush the unit, so stop here and have a plumber install them. It’s a common fix and makes every future flush simple.
The steps:
- Shut off the unit. Turn off the gas supply for gas units, or the breaker for electric units. Let the unit cool for 20 to 30 minutes.
- Close the hot and cold isolation valves. This cuts the unit off from your home’s plumbing.
- Connect the hoses. Run one hose from the pump outlet to the cold-side service port. Attach the second hose to the hot-side service port and drop its free end into the bucket.
- Fill the bucket with your vinegar or descaling solution and set the pump in it.
- Open both service port valves and turn on the pump. Let the solution circulate for 45 to 60 minutes. It flows in through the cold side, through the heat exchanger, and back into the bucket.
- Shut off the pump and disconnect the hose from the cold-side port. Dump the used solution.
- Rinse with clean water. Point the hot-side hose into an empty bucket or drain, then open the cold isolation valve and let fresh water run through for 5 to 10 minutes to clear out residue.
- Close the service ports, remove the hoses, and replace the port caps.
- Reopen both isolation valves and check every connection for drips.
- Clean the inlet water filter screen, and on many models, the air intake filter too. A soft brush and rinse usually does it.
- Restore gas or power and restart the unit. Open a hot faucet and let it run until the flow is steady to purge trapped air.
- Write down the date. Keep a simple log or photo of each flush. That record matters if you ever file a warranty claim.
What a Professional Service Includes That a DIY Flush Doesn’t
A DIY flush handles the most important job: clearing scale out of the heat exchanger. If you’re comfortable with the steps above, it’s worth doing. A full professional service goes further:
- Combustion analysis and burner inspection
- Venting inspection for blockages, corrosion, or loose joints
- Gas pressure verification
- Condensate trap and neutralizer service on condensing units
- Error code history review to catch developing problems
- Safety and sensor testing, plus documented service records for your warranty file
Professional tankless water heater maintenance also gets a trained set of eyes on the unit once a year, which is often when small issues like a weakening igniter get caught before they leave you without hot water.
Should You Install a Water Softener?
A whole-home softener removes calcium and magnesium before water reaches your tankless unit. That means less scale, longer gaps between descaling, and better protection for your dishwasher, washing machine, and fixtures.
It’s a fair question whether it’s worth it. A softener is an upfront investment, uses salt, and needs its own periodic maintenance. With moderately hard city water and a reliable annual descaling habit, plenty of Granbury homeowners do fine without one. If you’re on a private well, your water tests hard or very hard, or you’re seeing scale on every faucet in the house, a water softening system usually pays for itself in appliance life alone. Some homeowners pair it with whole-home water filtration to address taste and other contaminants at the same time.
Frequently Asked Questions
Can I use vinegar to descale a tankless water heater?
Yes. Undiluted white vinegar is the standard DIY descaler and works well for routine maintenance. Some manufacturers recommend their own descaling solution, so check your manual. Never use bleach or chemical drain cleaners.
How long does a tankless water heater last?
A well-maintained unit can last 20 years or more. Without regular descaling, it may fail much sooner, usually from heat exchanger damage.
What happens if I never descale my tankless water heater?
Scale keeps building until efficiency drops, error codes appear, and the unit eventually shuts down or the heat exchanger fails. You may also lose warranty coverage for that damage.
How long does descaling take?
Plan on about 90 minutes to 2 hours, including setup, the 45 to 60 minute circulation, rinsing, and restart.
Do I need isolation valves to flush a tankless unit?
In practice, yes. They let you seal the unit off and connect the pump. If your unit doesn’t have them, a plumber can install them, often in under an hour.
Does a water softener eliminate the need for descaling?
It reduces how often you’ll need to descale, but it doesn’t eliminate it. Annual service is still recommended.
How much does professional tankless maintenance cost?
A professional descaling and inspection generally runs in the low-to-mid hundreds of dollars, far less than a heat exchanger replacement. Justice Plumbing’s Plumbing Protection Plan bundles annual maintenance so it doesn’t slip through the cracks.
Keep Your Tankless Running Strong in Granbury and Hood County
Justice Plumbing has served Granbury and North Texas homeowners since 2001 (License #37533), and we’ve seen what years of mineral buildup do to a tankless unit that’s gone without service. Whether you’d rather hand off the flush entirely, need isolation valves installed, or opened the panel and didn’t like what you saw, we’ll get your unit back to full strength and give you the service records to prove it. Schedule your tankless descaling appointment today, and we’ll take it from there.





